Friday 11 November 2011
0
How to change IP Address??
How to change your IP address in less than a minute? The following trick gives you a step-by-step procedure to change your IP address.
1. Click on “Start” in the bottom left hand corner of screen.
2. Click on “Run”.
3. Type in “command” and hit ok.You should now be at an MSDOS prompt screen.
4. Type “ipconfig /release” just like that, and hit “enter”.
5. Type “exit” and leave the prompt.
6. Right-click on “Network Places” or “My Network Places” on your desktop.
7. Click on “properties”.
You should now be on a screen with something titled “Local Area Connection”, or something close to that.
8. Right click on “Local Area Connection” and click “properties”.
9. Double-click on the “Internet Protocol (TCP/IP)” from the list under the “General” tab.
10. Click on “Use the following IP address” under the “General” tab.
11. Create an IP address (It doesn’t matter what it is. I just type 1 and 2 until i fill the area up).
12. Press “Tab” and it should automatically fill in the “Subnet Mask” section with default numbers.
13. Hit the “Ok” button here.
14. Hit the “Ok” button again. You should now be back to the “Local Area Connection” screen.
15. Right-click back on “Local Area Connection” and go to properties again.
16. Go back to the “TCP/IP” settings.
17. This time, select “Obtain an IP address automatically”.
18. Hit “Ok”.
19. Hit “Ok” again.
20. You now have a new IP address.
Some ISPs do not support this type of procedure and hence there are chances of getting back the same old IP address even after trying this hack. In this case you need to switch off the modem and then switch it on to get the new IP address.
NOTE: All these tricks works only if you have a dynamic IP address. But if you have a static IP address you have no option to change your IP.
Its possible even to hide/change a static IP through proxy.There are several program that change your IP.But the following are few of the best ones
Hide My IP
If you use a Router then
1) open the router setup page in a web browser (ie 192.168.0.1)
2) find something like “Dynamic IP (DHCP) Internet Connection Type” here is where you can find info like the Router’s name and MAC Address
Mine looks like…
Host Name: WBR-2310 (router’s model number)
MAC Address: 00-17-9a-bb-4f-d0 (router’s MAC)
3) Change the last two letters of the MAC (ie 00-17-9a-bb-4f-FF)
4) save the routers settings…… (may take 30 sec)
5) Pull the Power Plug on your Cable modem, wait 5 sec plug back in..
You should have a NEW IP! Because you have a new MAC address. Mite work for static IP address but I dont have one so….
Note : If these methods are not working, then just PM me..
Subscribe us via E-mail and Add us on Facebook for daily updates and Plz also do click once on the ads displaying below or above the post for us.. :)
1. Click on “Start” in the bottom left hand corner of screen.
2. Click on “Run”.
3. Type in “command” and hit ok.You should now be at an MSDOS prompt screen.
4. Type “ipconfig /release” just like that, and hit “enter”.
5. Type “exit” and leave the prompt.
6. Right-click on “Network Places” or “My Network Places” on your desktop.
7. Click on “properties”.
You should now be on a screen with something titled “Local Area Connection”, or something close to that.
8. Right click on “Local Area Connection” and click “properties”.
9. Double-click on the “Internet Protocol (TCP/IP)” from the list under the “General” tab.
10. Click on “Use the following IP address” under the “General” tab.
11. Create an IP address (It doesn’t matter what it is. I just type 1 and 2 until i fill the area up).
12. Press “Tab” and it should automatically fill in the “Subnet Mask” section with default numbers.
13. Hit the “Ok” button here.
14. Hit the “Ok” button again. You should now be back to the “Local Area Connection” screen.
15. Right-click back on “Local Area Connection” and go to properties again.
16. Go back to the “TCP/IP” settings.
17. This time, select “Obtain an IP address automatically”.
18. Hit “Ok”.
19. Hit “Ok” again.
20. You now have a new IP address.
Some ISPs do not support this type of procedure and hence there are chances of getting back the same old IP address even after trying this hack. In this case you need to switch off the modem and then switch it on to get the new IP address.
NOTE: All these tricks works only if you have a dynamic IP address. But if you have a static IP address you have no option to change your IP.
Its possible even to hide/change a static IP through proxy.There are several program that change your IP.But the following are few of the best ones
Hide My IP
If you use a Router then
1) open the router setup page in a web browser (ie 192.168.0.1)
2) find something like “Dynamic IP (DHCP) Internet Connection Type” here is where you can find info like the Router’s name and MAC Address
Mine looks like…
Host Name: WBR-2310 (router’s model number)
MAC Address: 00-17-9a-bb-4f-d0 (router’s MAC)
3) Change the last two letters of the MAC (ie 00-17-9a-bb-4f-FF)
4) save the routers settings…… (may take 30 sec)
5) Pull the Power Plug on your Cable modem, wait 5 sec plug back in..
You should have a NEW IP! Because you have a new MAC address. Mite work for static IP address but I dont have one so….
Note : If these methods are not working, then just PM me..
Subscribe us via E-mail and Add us on Facebook for daily updates and Plz also do click once on the ads displaying below or above the post for us.. :)
Subscribe to:
Post Comments
(
Atom
)
0 Responses to “ How to change IP Address?? ”
Post a Comment